Giám đốc điều hành Walrus Amy Huang nói về lịch sử và triết lý của công ty
Phó chủ tịch Samuel Huang nói về các thế hệ máy bơm tăng áp khác nhau từ năm 1984 đến nay.
So sánh trực tiếp máy bơm tăng áp HQ 400 với model trước - tạo ra dòng nước và tiếng ồn
Simon Yen, quản lý của bộ phận bán hàng quốc tế dep. giải thích các tính năng độc đáo của Cú va chạm dòng HQ
Mark Lin, phó giám đốc bán hàng quốc tế dep. chia sẻ chiến lược và thách thức tiếp thị của Walrus
Nhà phân phối của công ty tại Ireland nói về những kinh nghiệm của anh khi làm việc với Walrus
Nhóm Walrus trả lời một số câu hỏi phổ biến nhất và thú vị nhất liên quan đến công ty và Máy bơm tăng áp Bơm tăng áp dòng HQ
HQ800
HQ800H
Trò chuyện hoặc liên hệ với Walrus
Nói chuyện ngay với Walrus trên Messenger
Gửi tin nhắn Nội bộ Đại diện bán hàng. Simon Yen của bơm Walrus. Anh ấy sẽ quay lại với bạn trong thời gian ngắn!
Liên kết
Tìm hiểu hơn về Walrus Pump đây.
WALRUS Danh mục máy bơm tăng áp HQ
Cause 1: No power supply. Remedy: Connect the electricity supply.
Cause 2: Too low/high voltage. Remedy: Check if supply voltage is within ± 10%.
Cause 3: Seized-up pump. Remedy:Place a screwdriver against the shaft end of the motor to check it the rotor will spin freely,and contact your pump supplier.
Cause 1: Seized-up pump. Remedy: Same as above.
Cause 2: Overloaded motor. Remedy: Turn off the power supply and restart or contact your pump supplier.
Cause 3: Poor water supply. Remedy: Check if pump suction inlet is blocked.
Cause 1: Existing pipe is leaking. Remedy: Fix the leakage.
Cause 2: Defective check valve. Remedy: Clean or replace with a new valve.
Cause 3: Pipe suck in air. Remedy: Check the suction pipe and water supply.
Cause 1: Leakage in suction pipe or air in the water. Remedy: Check the suction pipe and water supply.
Cause 2: Discharge flow is too low. Remedy: Set your tap on a higher water flow.
Ineffective grounding. Remedy: Reactivate grounding.
Cause 1: Poor water supply or air suck in. Remedy: 1. Turn off the power supply and open the refilling plug to release the air. Then restart.2. In case of long suction pipes, turn off the power and make sure if water supply is adequate.
Cause 2: Pressure set is too high. Remedy: Adjust pressure per XI.
Cause 3: Flow set is too small. Remedy: Adjust flow switch per XII.
Cause 1: 3-phase motor runs in wrong rotation. Remedy: Switch any of the 2 wires from motor terminal to correct rotation.
Cause 2: Poor water supply. Remedy: check if water supply is adequate and if the suction pipe is blocked.
Cause: The overheating protector is mounted directly on the motor windings. It will stop the motor automatically when the motor temperature is up to abnormal, and restart the motor after the temperature back to normal in 20 minutes.
Remedy:
Remedy: a. Check and fix the leakage in discharge piping, faucets, and valves.
Cause: The pump's pressure switch has been set accurately. Please do not try to adjust except by qualified personnel.
Remedy:
Cause: The overheating protector is mounted directly on the motor windings. It will stop the motor automatically when the motor temperature is up to abnormal, and restart the motor after the temperature back to normal in 20 minutes.
Remedy:
Remedy:
Jan 10, 2020
Apr 09, 2020
Apr 08, 2020