바다 코끼리 CEO 에이미 황 은 회사의 역사와 철학에 대해 이야기합니다.
사무엘 황 부사장은 1984 년부터 현재까지 다양한 세대의 부스터 펌프에 대해 이야기합니다.
이전 모델과 HQ 400 부스터 펌프의 실시간 비교 – 물 흐름 및 소음 발생
사이먼 왜, 국제 영업 부서 관리자 HQ 시리즈 부스터 범프의 고유 한 기능 설명
마크 린, 국제 영업부 차장 바다 코끼리 의 마케팅 전략 및 과제 공유
아일랜드에있는이 회사의 유통 업체는 바다 코끼리 와의 경험에 대해 이야기합니다.
바다 코끼리 팀이 회사 및 HQ 시리즈 부스터 펌프와 관련하여 가장 일반적이고 가장 흥미로운 질문에 답변
HQ800
HQ800H
채팅 또는 연락 바다 코끼리
지금 채팅 메신저에서 바다 코끼리 와 함께
메시지를 보내다 INT. 영업 담당자. 사이먼 왜 자동 유량 제어 펌프. 그는 곧 당신에게 돌아올 것입니다!
링크
에 대해 자세히 알아보십시오 자동 유량 제어 펌프 여기.
바다 코끼리 HQ 부스터 펌프 카탈로그
Cause 1: No power supply. Remedy: Connect the electricity supply.
Cause 2: Too low/high voltage. Remedy: Check if supply voltage is within ± 10%.
Cause 3: Seized-up pump. Remedy:Place a screwdriver against the shaft end of the motor to check it the rotor will spin freely,and contact your pump supplier.
Cause 1: Seized-up pump. Remedy: Same as above.
Cause 2: Overloaded motor. Remedy: Turn off the power supply and restart or contact your pump supplier.
Cause 3: Poor water supply. Remedy: Check if pump suction inlet is blocked.
Cause 1: Existing pipe is leaking. Remedy: Fix the leakage.
Cause 2: Defective check valve. Remedy: Clean or replace with a new valve.
Cause 3: Pipe suck in air. Remedy: Check the suction pipe and water supply.
Cause 1: Leakage in suction pipe or air in the water. Remedy: Check the suction pipe and water supply.
Cause 2: Discharge flow is too low. Remedy: Set your tap on a higher water flow.
Ineffective grounding. Remedy: Reactivate grounding.
Cause 1: Poor water supply or air suck in. Remedy: 1. Turn off the power supply and open the refilling plug to release the air. Then restart.2. In case of long suction pipes, turn off the power and make sure if water supply is adequate.
Cause 2: Pressure set is too high. Remedy: Adjust pressure per XI.
Cause 3: Flow set is too small. Remedy: Adjust flow switch per XII.
Cause 1: 3-phase motor runs in wrong rotation. Remedy: Switch any of the 2 wires from motor terminal to correct rotation.
Cause 2: Poor water supply. Remedy: check if water supply is adequate and if the suction pipe is blocked.
Cause: The overheating protector is mounted directly on the motor windings. It will stop the motor automatically when the motor temperature is up to abnormal, and restart the motor after the temperature back to normal in 20 minutes.
Remedy:
Remedy: a. Check and fix the leakage in discharge piping, faucets, and valves.
Cause: The pump's pressure switch has been set accurately. Please do not try to adjust except by qualified personnel.
Remedy:
Cause: The overheating protector is mounted directly on the motor windings. It will stop the motor automatically when the motor temperature is up to abnormal, and restart the motor after the temperature back to normal in 20 minutes.
Remedy:
Remedy: